Lockouts · Toronto
Break-In Damage Lock Repair
The back door looks closed until you touch it. The edge is crushed where a bar went in, the latch is bent sideways, and the door swings free with a gentle push no matter how you turn the key.
Break-In Damage Lock Repair
In plain words
Break-ins seldom come through the door with the strongest lock. Sliding patio doors are lifted off their track or pried at the latch, the garage man-door carries a light knob lock, a basement walkout is out of sight, and a storefront's narrow-stile deadbolt sits behind a bendable aluminum edge. Each needs its own repair: anti-lift blocks and a foot bolt for the slider, a proper deadbolt and reinforced strike for the side door, a latch guard and repaired stile for the shop. Break-in damage lock repair covers whichever opening was attacked and looks over the others while the tools are already out.
How the visit goesThere is a hole where the cylinder used to be. Somebody twisted it out of the deadbolt with a wrench, and now the empty bore looks straight through to the kitchen, with the bolt still stuck in the frame.
Toronto
How the visit goes
Lock, frame or door: which one failed
Three components can fail in a forced entry and they are repaired differently, so the locksmith sorts them out before quoting. Lock failure is a broken cylinder, bolt or latch and is answered with hardware. Frame failure is a torn strike or split jamb and is answered with a boxed strike, repair plates, long screws and sometimes new wood. Door failure is a crushed edge, a split around the bore or a bent hinge leaf and is answered with edge reinforcement or, when the slab itself is broken, a door installer. Naming which of the three happened, and often all three, shows you what the locksmith completes tonight and what is handed to another trade.
Rekeying what a taken key fits
Every cylinder that a missing key could open is rekeyed or replaced before the locksmith leaves. On a serviceable pin-tumbler cylinder, the plug is slid free with a follower so the springs stay put, the bottom pins are exchanged for a new combination and a fresh key is cut; a cylinder that cannot be rekeyed this way is replaced instead. Front, back, side and garage doors are brought onto one new key where their keyways and systems allow it, and the mailbox and padlocks are handled too. Remotes for a garage opener that left in a stolen car are erased from the opener and a new one programmed. The old key still fits the keyway; it simply turns nothing anymore.
A door that closes and locks again
The visit ends with the door tested the way it will be used. The bolt is thrown and withdrawn with the door open, then closed, and it must slide home without dragging on the strike or stopping short of full extension. The latch catches when the door is pushed to, not slammed. The door meets its weatherstrip evenly and the thumb-turn works from inside without a key. You try it yourself before the locksmith packs up, with your own new key, so the first time the household locks up that night is not the first time anyone has tried the door.
Break-In Damage Lock Repair
In the van
- Three-inch strike and hinge screws
- Plywood and cleats for boarding
- Security strike box
- Wrap-around door edge reinforcer
- Jamb repair plate
What affects the quote
Same fees day, night or weekend
1Sliding door hardware
Putting a slider back on its track, replacing its latch and adding anti-lift blocks, a foot bolt or an auxiliary lock is a different parts list from a hinged door, and is quoted as such.
2Method of jamb repair
Bonding a split with epoxy and a repair plate is one line; fitting a new section of wood is another; a full jamb leg through a carpenter is quoted by that trade.
3Strike and hinge reinforcement
A security strike box, hinge reinforcement plates and three-inch screws on both sides of the door are listed as their own items, so you can see what strengthens the frame beyond replacing what broke.
Break-In Damage Lock Repair: questions
How long does a break-in repair take?
It depends on how much gave way. A new lockset and a reinforced strike on a sound frame is a modest job. Bonding a split jamb, sleeving a crushed door edge, reinforcing the hinges and rekeying several cylinders takes longer, and a shattered frame means a securing visit now and a second visit after the carpenter. The locksmith gives a sense of the time once the damage has been seen, and the opening is secured before leaving even when a part has to be ordered.
Should I upgrade to a stronger deadbolt while you are here?
It is the natural moment, because the door is already open for repair. A deadbolt with a full one-inch throw, a hardened insert against sawing and a low-profile face that resists a wrench grip, graded to a recognised durability standard, takes little extra effort to fit now compared with a return visit. Pair it with the reinforced strike and long screws and the door becomes hard to attack from any side. The choice is yours; the locksmith shows the options and lets you decide.
Is a smart lock a good replacement after a break-in?
It can be, with the same reinforcement behind it. A keypad or app-controlled deadbolt eases the problem of stolen keys, since codes are changed in seconds and a lost phone is unpaired rather than rekeyed. Its bolt still needs a boxed strike and long screws, because the frame is what failed; a keyed override should be rekeyed too, with any spare left with a trusted person, not hidden outside; a cylinder-free model needs no override key. Choose one with a full-throw bolt and fit it to a reinforced door edge.
Lockout Services
- Business Lockout ServiceYou signed the lease on the unit last week and the landlord handed over possession, but the…
- Broken Key ExtractionThe key went in like any other morning, you turned it, and something gave with a small metallic…
- Seized & Jammed Lock OpeningThe old mortise lock on the front door of the house turns the key halfway and stops with a dull…
Break-In Damage Lock Repair near you
Every lock service we provide in Toronto starts with the same first step, which is looking at the door properly before deciding anything. The individual pages below explain what that look involves for each job, how the work is carried out, and what to expect from the hardware afterwards.